/*
 * (C) Copyright 2000-2011
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 *
 */

/*
 * IDE support
 */

#include <common.h>
#include <config.h>
#include <watchdog.h>
#include <command.h>
#include <image.h>
#include <asm/byteorder.h>
#include <asm/io.h>

#if defined(CONFIG_IDE_8xx_DIRECT) || defined(CONFIG_IDE_PCMCIA)
# include <pcmcia.h>
#endif

#ifdef CONFIG_8xx
# include <mpc8xx.h>
#endif

#ifdef CONFIG_MPC5xxx
#include <mpc5xxx.h>
#endif

#include <ide.h>
#include <ata.h>

#ifdef CONFIG_STATUS_LED
# include <status_led.h>
#endif

#ifdef CONFIG_IDE_8xx_DIRECT
DECLARE_GLOBAL_DATA_PTR;
#endif

#ifdef __PPC__
# define EIEIO		__asm__ volatile ("eieio")
# define SYNC		__asm__ volatile ("sync")
#else
# define EIEIO		/* nothing */
# define SYNC		/* nothing */
#endif

#ifdef CONFIG_IDE_8xx_DIRECT
/* Timings for IDE Interface
 *
 * SETUP / LENGTH / HOLD - cycles valid for 50 MHz clk
 * 70	   165	    30	   PIO-Mode 0, [ns]
 *  4	     9	     2		       [Cycles]
 * 50	   125	    20	   PIO-Mode 1, [ns]
 *  3	     7	     2		       [Cycles]
 * 30	   100	    15	   PIO-Mode 2, [ns]
 *  2	     6	     1		       [Cycles]
 * 30	    80	    10	   PIO-Mode 3, [ns]
 *  2	     5	     1		       [Cycles]
 * 25	    70	    10	   PIO-Mode 4, [ns]
 *  2	     4	     1		       [Cycles]
 */

const static pio_config_t pio_config_ns [IDE_MAX_PIO_MODE+1] =
{
    /*	Setup  Length  Hold  */
	{ 70,	165,	30 },		/* PIO-Mode 0, [ns]	*/
	{ 50,	125,	20 },		/* PIO-Mode 1, [ns]	*/
	{ 30,	101,	15 },		/* PIO-Mode 2, [ns]	*/
	{ 30,	 80,	10 },		/* PIO-Mode 3, [ns]	*/
	{ 25,	 70,	10 },		/* PIO-Mode 4, [ns]	*/
};

static pio_config_t pio_config_clk [IDE_MAX_PIO_MODE+1];

#ifndef	CONFIG_SYS_PIO_MODE
#define	CONFIG_SYS_PIO_MODE	0		/* use a relaxed default */
#endif
static int pio_mode = CONFIG_SYS_PIO_MODE;

/* Make clock cycles and always round up */

#define PCMCIA_MK_CLKS( t, T ) (( (t) * (T) + 999U ) / 1000U )

#endif /* CONFIG_IDE_8xx_DIRECT */

/* ------------------------------------------------------------------------- */

/* Current I/O Device	*/
static int curr_device = -1;

/* Current offset for IDE0 / IDE1 bus access	*/
ulong ide_bus_offset[CONFIG_SYS_IDE_MAXBUS] = {
#if defined(CONFIG_SYS_ATA_IDE0_OFFSET)
	CONFIG_SYS_ATA_IDE0_OFFSET,
#endif
#if defined(CONFIG_SYS_ATA_IDE1_OFFSET) && (CONFIG_SYS_IDE_MAXBUS > 1)
	CONFIG_SYS_ATA_IDE1_OFFSET,
#endif
};

static int ide_bus_ok[CONFIG_SYS_IDE_MAXBUS];

block_dev_desc_t ide_dev_desc[CONFIG_SYS_IDE_MAXDEVICE];
/* ------------------------------------------------------------------------- */

#ifdef CONFIG_IDE_LED
# if !defined(CONFIG_BMS2003)	&& \
     !defined(CONFIG_CPC45)	&& \
     !defined(CONFIG_KUP4K) && \
     !defined(CONFIG_KUP4X)
static void  ide_led   (uchar led, uchar status);
#else
extern void  ide_led   (uchar led, uchar status);
#endif
#else
#define ide_led(a,b)	/* dummy */
#endif

#ifdef CONFIG_IDE_RESET
static void  ide_reset (void);
#else
#define ide_reset()	/* dummy */
#endif

static void  ide_ident (block_dev_desc_t *dev_desc);
static uchar ide_wait  (int dev, ulong t);

#define IDE_TIME_OUT	2000	/* 2 sec timeout */

#define ATAPI_TIME_OUT	7000	/* 7 sec timeout (5 sec seems to work...) */

#define IDE_SPIN_UP_TIME_OUT 5000 /* 5 sec spin-up timeout */

static void input_data(int dev, ulong *sect_buf, int words);
static void output_data(int dev, const ulong *sect_buf, int words);
static void ident_cpy (unsigned char *dest, unsigned char *src, unsigned int len);

#ifndef CONFIG_SYS_ATA_PORT_ADDR
#define CONFIG_SYS_ATA_PORT_ADDR(port) (port)
#endif

#ifdef CONFIG_ATAPI
static void	atapi_inquiry(block_dev_desc_t *dev_desc);
ulong atapi_read (int device, lbaint_t blknr, ulong blkcnt, void *buffer);
#endif


#ifdef CONFIG_IDE_8xx_DIRECT
static void set_pcmcia_timing (int pmode);
#endif

/* ------------------------------------------------------------------------- */

int do_ide(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
{
	int rcode = 0;

	switch (argc) {
	case 0:
	case 1:
		return CMD_RET_USAGE;
	case 2:
		if (strncmp(argv[1], "res", 3) == 0) {
			puts("\nReset IDE"
#ifdef CONFIG_IDE_8xx_DIRECT
			     " on PCMCIA " PCMCIA_SLOT_MSG
#endif
			     ": ");

			ide_init();
			return 0;
		} else if (strncmp(argv[1], "inf", 3) == 0) {
			int i;

			putc('\n');

			for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i) {
				if (ide_dev_desc[i].type == DEV_TYPE_UNKNOWN)
					continue;  /* list only known devices */
				printf("IDE device %d: ", i);
				dev_print(&ide_dev_desc[i]);
			}
			return 0;

		} else if (strncmp(argv[1], "dev", 3) == 0) {
			if ((curr_device < 0)
			    || (curr_device >= CONFIG_SYS_IDE_MAXDEVICE)) {
				puts("\nno IDE devices available\n");
				return 1;
			}
			printf("\nIDE device %d: ", curr_device);
			dev_print(&ide_dev_desc[curr_device]);
			return 0;
		} else if (strncmp(argv[1], "part", 4) == 0) {
			int dev, ok;

			for (ok = 0, dev = 0;
			     dev < CONFIG_SYS_IDE_MAXDEVICE;
			     ++dev) {
				if (ide_dev_desc[dev].part_type !=
				    PART_TYPE_UNKNOWN) {
					++ok;
					if (dev)
						putc('\n');
					print_part(&ide_dev_desc[dev]);
				}
			}
			if (!ok) {
				puts("\nno IDE devices available\n");
				rcode++;
			}
			return rcode;
		}
		return CMD_RET_USAGE;
	case 3:
		if (strncmp(argv[1], "dev", 3) == 0) {
			int dev = (int) simple_strtoul(argv[2], NULL, 10);

			printf("\nIDE device %d: ", dev);
			if (dev >= CONFIG_SYS_IDE_MAXDEVICE) {
				puts("unknown device\n");
				return 1;
			}
			dev_print(&ide_dev_desc[dev]);
			/*ide_print (dev); */

			if (ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN)
				return 1;

			curr_device = dev;

			puts("... is now current device\n");

			return 0;
		} else if (strncmp(argv[1], "part", 4) == 0) {
			int dev = (int) simple_strtoul(argv[2], NULL, 10);

			if (ide_dev_desc[dev].part_type != PART_TYPE_UNKNOWN) {
				print_part(&ide_dev_desc[dev]);
			} else {
				printf("\nIDE device %d not available\n",
				       dev);
				rcode = 1;
			}
			return rcode;
		}

		return CMD_RET_USAGE;
	default:
		/* at least 4 args */

		if (strcmp(argv[1], "read") == 0) {
			ulong addr = simple_strtoul(argv[2], NULL, 16);
			ulong cnt = simple_strtoul(argv[4], NULL, 16);
			ulong n;

#ifdef CONFIG_SYS_64BIT_LBA
			lbaint_t blk = simple_strtoull(argv[3], NULL, 16);

			printf("\nIDE read: device %d block # %lld, count %ld ... ",
				curr_device, blk, cnt);
#else
			lbaint_t blk = simple_strtoul(argv[3], NULL, 16);

			printf("\nIDE read: device %d block # %ld, count %ld ... ",
				curr_device, blk, cnt);
#endif

			n = ide_dev_desc[curr_device].block_read(curr_device,
								 blk, cnt,
								 (ulong *)addr);
			/* flush cache after read */
			flush_cache(addr,
				    cnt * ide_dev_desc[curr_device].blksz);

			printf("%ld blocks read: %s\n",
			       n, (n == cnt) ? "OK" : "ERROR");
			if (n == cnt)
				return 0;
			else
				return 1;
		} else if (strcmp(argv[1], "write") == 0) {
			ulong addr = simple_strtoul(argv[2], NULL, 16);
			ulong cnt = simple_strtoul(argv[4], NULL, 16);
			ulong n;

#ifdef CONFIG_SYS_64BIT_LBA
			lbaint_t blk = simple_strtoull(argv[3], NULL, 16);

			printf("\nIDE write: device %d block # %lld, count %ld ... ",
				curr_device, blk, cnt);
#else
			lbaint_t blk = simple_strtoul(argv[3], NULL, 16);

			printf("\nIDE write: device %d block # %ld, count %ld ... ",
				curr_device, blk, cnt);
#endif
			n = ide_write(curr_device, blk, cnt, (ulong *) addr);

			printf("%ld blocks written: %s\n",
				n, (n == cnt) ? "OK" : "ERROR");
			if (n == cnt)
				return 0;
			else
				return 1;
		} else {
			return CMD_RET_USAGE;
		}

		return rcode;
	}
}

int do_diskboot(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
{
	char *boot_device = NULL;
	char *ep;
	int dev, part = 0;
	ulong addr, cnt;
	disk_partition_t info;
	image_header_t *hdr;

#if defined(CONFIG_FIT)
	const void *fit_hdr = NULL;
#endif

	bootstage_mark(BOOTSTAGE_ID_IDE_START);
	switch (argc) {
	case 1:
		addr = CONFIG_SYS_LOAD_ADDR;
		boot_device = getenv("bootdevice");
		break;
	case 2:
		addr = simple_strtoul(argv[1], NULL, 16);
		boot_device = getenv("bootdevice");
		break;
	case 3:
		addr = simple_strtoul(argv[1], NULL, 16);
		boot_device = argv[2];
		break;
	default:
		bootstage_error(BOOTSTAGE_ID_IDE_ADDR);
		return CMD_RET_USAGE;
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_ADDR);

	if (!boot_device) {
		puts("\n** No boot device **\n");
		bootstage_error(BOOTSTAGE_ID_IDE_BOOT_DEVICE);
		return 1;
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_BOOT_DEVICE);

	dev = simple_strtoul(boot_device, &ep, 16);

	if (ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN) {
		printf("\n** Device %d not available\n", dev);
		bootstage_error(BOOTSTAGE_ID_IDE_TYPE);
		return 1;
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_TYPE);

	if (*ep) {
		if (*ep != ':') {
			puts("\n** Invalid boot device, use `dev[:part]' **\n");
			bootstage_error(BOOTSTAGE_ID_IDE_PART);
			return 1;
		}
		part = simple_strtoul(++ep, NULL, 16);
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_PART);

	if (get_partition_info(&ide_dev_desc[dev], part, &info)) {
		bootstage_error(BOOTSTAGE_ID_IDE_PART_INFO);
		return 1;
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_PART_INFO);

	if ((strncmp((char *)info.type, BOOT_PART_TYPE, sizeof(info.type)) != 0)
	    &&
	    (strncmp((char *)info.type, BOOT_PART_COMP, sizeof(info.type)) != 0)
	   ) {
		printf("\n** Invalid partition type \"%.32s\"" " (expect \""
			BOOT_PART_TYPE "\")\n",
			info.type);
		bootstage_error(BOOTSTAGE_ID_IDE_PART_TYPE);
		return 1;
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_PART_TYPE);

	printf("\nLoading from IDE device %d, partition %d: "
	       "Name: %.32s  Type: %.32s\n", dev, part, info.name, info.type);

	debug("First Block: %ld,  # of blocks: %ld, Block Size: %ld\n",
	      info.start, info.size, info.blksz);

	if (ide_dev_desc[dev].
	    block_read(dev, info.start, 1, (ulong *) addr) != 1) {
		printf("** Read error on %d:%d\n", dev, part);
		bootstage_error(BOOTSTAGE_ID_IDE_PART_READ);
		return 1;
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_PART_READ);

	switch (genimg_get_format((void *) addr)) {
	case IMAGE_FORMAT_LEGACY:
		hdr = (image_header_t *) addr;

		bootstage_mark(BOOTSTAGE_ID_IDE_FORMAT);

		if (!image_check_hcrc(hdr)) {
			puts("\n** Bad Header Checksum **\n");
			bootstage_error(BOOTSTAGE_ID_IDE_CHECKSUM);
			return 1;
		}
		bootstage_mark(BOOTSTAGE_ID_IDE_CHECKSUM);

		image_print_contents(hdr);

		cnt = image_get_image_size(hdr);
		break;
#if defined(CONFIG_FIT)
	case IMAGE_FORMAT_FIT:
		fit_hdr = (const void *) addr;
		puts("Fit image detected...\n");

		cnt = fit_get_size(fit_hdr);
		break;
#endif
	default:
		bootstage_error(BOOTSTAGE_ID_IDE_FORMAT);
		puts("** Unknown image type\n");
		return 1;
	}

	cnt += info.blksz - 1;
	cnt /= info.blksz;
	cnt -= 1;

	if (ide_dev_desc[dev].block_read(dev, info.start + 1, cnt,
					 (ulong *)(addr + info.blksz)) != cnt) {
		printf("** Read error on %d:%d\n", dev, part);
		bootstage_error(BOOTSTAGE_ID_IDE_READ);
		return 1;
	}
	bootstage_mark(BOOTSTAGE_ID_IDE_READ);

#if defined(CONFIG_FIT)
	/* This cannot be done earlier, we need complete FIT image in RAM first */
	if (genimg_get_format((void *) addr) == IMAGE_FORMAT_FIT) {
		if (!fit_check_format(fit_hdr)) {
			bootstage_error(BOOTSTAGE_ID_IDE_FIT_READ);
			puts("** Bad FIT image format\n");
			return 1;
		}
		bootstage_mark(BOOTSTAGE_ID_IDE_FIT_READ_OK);
		fit_print_contents(fit_hdr);
	}
#endif

	/* Loading ok, update default load address */

	load_addr = addr;

	return bootm_maybe_autostart(cmdtp, argv[0]);
}

/* ------------------------------------------------------------------------- */

inline void __ide_outb(int dev, int port, unsigned char val)
{
	debug("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n",
	      dev, port, val,
	      (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));

#if defined(CONFIG_IDE_AHB)
	if (port) {
		/* write command */
		ide_write_register(dev, port, val);
	} else {
		/* write data */
		outb(val, (ATA_CURR_BASE(dev)));
	}
#else
	outb(val, (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
#endif
}

void ide_outb(int dev, int port, unsigned char val)
	__attribute__ ((weak, alias("__ide_outb")));

inline unsigned char __ide_inb(int dev, int port)
{
	uchar val;

#if defined(CONFIG_IDE_AHB)
	val = ide_read_register(dev, port);
#else
	val = inb((ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)));
#endif

	debug("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
	      dev, port,
	      (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)), val);
	return val;
}

unsigned char ide_inb(int dev, int port)
	__attribute__ ((weak, alias("__ide_inb")));

#ifdef CONFIG_TUNE_PIO
inline int __ide_set_piomode(int pio_mode)
{
	return 0;
}

inline int ide_set_piomode(int pio_mode)
	__attribute__ ((weak, alias("__ide_set_piomode")));
#endif

void ide_init(void)
{

#ifdef CONFIG_IDE_8xx_DIRECT
	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
	volatile pcmconf8xx_t *pcmp = &(immr->im_pcmcia);
#endif
	unsigned char c;
	int i, bus;

#if defined(CONFIG_SC3)
	unsigned int ata_reset_time = ATA_RESET_TIME;
#endif
#ifdef CONFIG_IDE_8xx_PCCARD
	extern int pcmcia_on(void);
	extern int ide_devices_found;	/* Initialized in check_ide_device() */
#endif /* CONFIG_IDE_8xx_PCCARD */

#ifdef CONFIG_IDE_PREINIT
	extern int ide_preinit(void);

	WATCHDOG_RESET();

	if (ide_preinit()) {
		puts("ide_preinit failed\n");
		return;
	}
#endif /* CONFIG_IDE_PREINIT */

#ifdef CONFIG_IDE_8xx_PCCARD
	extern int pcmcia_on(void);
	extern int ide_devices_found;	/* Initialized in check_ide_device() */

	WATCHDOG_RESET();

	ide_devices_found = 0;
	/* initialize the PCMCIA IDE adapter card */
	pcmcia_on();
	if (!ide_devices_found)
		return;
	udelay(1000000);	/* 1 s */
#endif /* CONFIG_IDE_8xx_PCCARD */

	WATCHDOG_RESET();

#ifdef CONFIG_IDE_8xx_DIRECT
	/* Initialize PIO timing tables */
	for (i = 0; i <= IDE_MAX_PIO_MODE; ++i) {
		pio_config_clk[i].t_setup =
			PCMCIA_MK_CLKS(pio_config_ns[i].t_setup, gd->bus_clk);
		pio_config_clk[i].t_length =
			PCMCIA_MK_CLKS(pio_config_ns[i].t_length,
				       gd->bus_clk);
		pio_config_clk[i].t_hold =
			PCMCIA_MK_CLKS(pio_config_ns[i].t_hold, gd->bus_clk);
		debug("PIO Mode %d: setup=%2d ns/%d clk" "  len=%3d ns/%d clk"
		      "  hold=%2d ns/%d clk\n", i, pio_config_ns[i].t_setup,
		      pio_config_clk[i].t_setup, pio_config_ns[i].t_length,
		      pio_config_clk[i].t_length, pio_config_ns[i].t_hold,
		      pio_config_clk[i].t_hold);
	}
#endif /* CONFIG_IDE_8xx_DIRECT */

	/*
	 * Reset the IDE just to be sure.
	 * Light LED's to show
	 */
	ide_led((LED_IDE1 | LED_IDE2), 1);	/* LED's on     */

	/* ATAPI Drives seems to need a proper IDE Reset */
	ide_reset();

#ifdef CONFIG_IDE_8xx_DIRECT
	/* PCMCIA / IDE initialization for common mem space */
	pcmp->pcmc_pgcrb = 0;

	/* start in PIO mode 0 - most relaxed timings */
	pio_mode = 0;
	set_pcmcia_timing(pio_mode);
#endif /* CONFIG_IDE_8xx_DIRECT */

	/*
	 * Wait for IDE to get ready.
	 * According to spec, this can take up to 31 seconds!
	 */
	for (bus = 0; bus < CONFIG_SYS_IDE_MAXBUS; ++bus) {
		int dev =
			bus * (CONFIG_SYS_IDE_MAXDEVICE /
			       CONFIG_SYS_IDE_MAXBUS);

#ifdef CONFIG_IDE_8xx_PCCARD
		/* Skip non-ide devices from probing */
		if ((ide_devices_found & (1 << bus)) == 0) {
			ide_led((LED_IDE1 | LED_IDE2), 0);	/* LED's off */
			continue;
		}
#endif
		printf("Bus %d: ", bus);

		ide_bus_ok[bus] = 0;

		/* Select device
		 */
		udelay(100000);	/* 100 ms */
		ide_outb(dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
		udelay(100000);	/* 100 ms */
		i = 0;
		do {
			udelay(10000);	/* 10 ms */

			c = ide_inb(dev, ATA_STATUS);
			i++;
#if defined(CONFIG_SC3)
			if (i > (ata_reset_time * 100)) {
#else
			if (i > (ATA_RESET_TIME * 100)) {
#endif
				puts("** Timeout **\n");
				/* LED's off */
				ide_led((LED_IDE1 | LED_IDE2), 0);
				return;
			}
			if ((i >= 100) && ((i % 100) == 0))
				putc('.');

		} while (c & ATA_STAT_BUSY);

		if (c & (ATA_STAT_BUSY | ATA_STAT_FAULT)) {
			puts("not available  ");
			debug("Status = 0x%02X ", c);
#ifndef CONFIG_ATAPI		/* ATAPI Devices do not set DRDY */
		} else if ((c & ATA_STAT_READY) == 0) {
			puts("not available  ");
			debug("Status = 0x%02X ", c);
#endif
		} else {
			puts("OK ");
			ide_bus_ok[bus] = 1;
		}
		WATCHDOG_RESET();
	}

	putc('\n');

	ide_led((LED_IDE1 | LED_IDE2), 0);	/* LED's off    */

	curr_device = -1;
	for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i) {
#ifdef CONFIG_IDE_LED
		int led = (IDE_BUS(i) == 0) ? LED_IDE1 : LED_IDE2;
#endif
		ide_dev_desc[i].type = DEV_TYPE_UNKNOWN;
		ide_dev_desc[i].if_type = IF_TYPE_IDE;
		ide_dev_desc[i].dev = i;
		ide_dev_desc[i].part_type = PART_TYPE_UNKNOWN;
		ide_dev_desc[i].blksz = 0;
		ide_dev_desc[i].lba = 0;
		ide_dev_desc[i].block_read = ide_read;
		ide_dev_desc[i].block_write = ide_write;
		if (!ide_bus_ok[IDE_BUS(i)])
			continue;
		ide_led(led, 1);	/* LED on       */
		ide_ident(&ide_dev_desc[i]);
		ide_led(led, 0);	/* LED off      */
		dev_print(&ide_dev_desc[i]);

		if ((ide_dev_desc[i].lba > 0) && (ide_dev_desc[i].blksz > 0)) {
			/* initialize partition type */
			init_part(&ide_dev_desc[i]);
			if (curr_device < 0)
				curr_device = i;
		}
	}
	WATCHDOG_RESET();
}

/* ------------------------------------------------------------------------- */

#ifdef CONFIG_PARTITIONS
block_dev_desc_t *ide_get_dev(int dev)
{
	return (dev < CONFIG_SYS_IDE_MAXDEVICE) ? &ide_dev_desc[dev] : NULL;
}
#endif


#ifdef CONFIG_IDE_8xx_DIRECT

static void set_pcmcia_timing(int pmode)
{
	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
	volatile pcmconf8xx_t *pcmp = &(immr->im_pcmcia);
	ulong timings;

	debug("Set timing for PIO Mode %d\n", pmode);

	timings = PCMCIA_SHT(pio_config_clk[pmode].t_hold)
		| PCMCIA_SST(pio_config_clk[pmode].t_setup)
		| PCMCIA_SL(pio_config_clk[pmode].t_length);

	/*
	 * IDE 0
	 */
	pcmp->pcmc_pbr0 = CONFIG_SYS_PCMCIA_PBR0;
	pcmp->pcmc_por0 = CONFIG_SYS_PCMCIA_POR0
#if (CONFIG_SYS_PCMCIA_POR0 != 0)
		| timings
#endif
		;
	debug("PBR0: %08x  POR0: %08x\n", pcmp->pcmc_pbr0, pcmp->pcmc_por0);

	pcmp->pcmc_pbr1 = CONFIG_SYS_PCMCIA_PBR1;
	pcmp->pcmc_por1 = CONFIG_SYS_PCMCIA_POR1
#if (CONFIG_SYS_PCMCIA_POR1 != 0)
		| timings
#endif
		;
	debug("PBR1: %08x  POR1: %08x\n", pcmp->pcmc_pbr1, pcmp->pcmc_por1);

	pcmp->pcmc_pbr2 = CONFIG_SYS_PCMCIA_PBR2;
	pcmp->pcmc_por2 = CONFIG_SYS_PCMCIA_POR2
#if (CONFIG_SYS_PCMCIA_POR2 != 0)
		| timings
#endif
		;
	debug("PBR2: %08x  POR2: %08x\n", pcmp->pcmc_pbr2, pcmp->pcmc_por2);

	pcmp->pcmc_pbr3 = CONFIG_SYS_PCMCIA_PBR3;
	pcmp->pcmc_por3 = CONFIG_SYS_PCMCIA_POR3
#if (CONFIG_SYS_PCMCIA_POR3 != 0)
		| timings
#endif
		;
	debug("PBR3: %08x  POR3: %08x\n", pcmp->pcmc_pbr3, pcmp->pcmc_por3);

	/*
	 * IDE 1
	 */
	pcmp->pcmc_pbr4 = CONFIG_SYS_PCMCIA_PBR4;
	pcmp->pcmc_por4 = CONFIG_SYS_PCMCIA_POR4
#if (CONFIG_SYS_PCMCIA_POR4 != 0)
		| timings
#endif
		;
	debug("PBR4: %08x  POR4: %08x\n", pcmp->pcmc_pbr4, pcmp->pcmc_por4);

	pcmp->pcmc_pbr5 = CONFIG_SYS_PCMCIA_PBR5;
	pcmp->pcmc_por5 = CONFIG_SYS_PCMCIA_POR5
#if (CONFIG_SYS_PCMCIA_POR5 != 0)
		| timings
#endif
		;
	debug("PBR5: %08x  POR5: %08x\n", pcmp->pcmc_pbr5, pcmp->pcmc_por5);

	pcmp->pcmc_pbr6 = CONFIG_SYS_PCMCIA_PBR6;
	pcmp->pcmc_por6 = CONFIG_SYS_PCMCIA_POR6
#if (CONFIG_SYS_PCMCIA_POR6 != 0)
		| timings
#endif
		;
	debug("PBR6: %08x  POR6: %08x\n", pcmp->pcmc_pbr6, pcmp->pcmc_por6);

	pcmp->pcmc_pbr7 = CONFIG_SYS_PCMCIA_PBR7;
	pcmp->pcmc_por7 = CONFIG_SYS_PCMCIA_POR7
#if (CONFIG_SYS_PCMCIA_POR7 != 0)
		| timings
#endif
		;
	debug("PBR7: %08x  POR7: %08x\n", pcmp->pcmc_pbr7, pcmp->pcmc_por7);

}

#endif /* CONFIG_IDE_8xx_DIRECT */

/* ------------------------------------------------------------------------- */

/* We only need to swap data if we are running on a big endian cpu. */
/* But Au1x00 cpu:s already swaps data in big endian mode! */
#if defined(__LITTLE_ENDIAN) || \
   (defined(CONFIG_SOC_AU1X00) && !defined(CONFIG_GTH2))
#define input_swap_data(x,y,z) input_data(x,y,z)
#else
static void input_swap_data(int dev, ulong *sect_buf, int words)
{
#if defined(CONFIG_CPC45)
	uchar i;
	volatile uchar *pbuf_even =
		(uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
	volatile uchar *pbuf_odd =
		(uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
	ushort *dbuf = (ushort *) sect_buf;

	while (words--) {
		for (i = 0; i < 2; i++) {
			*(((uchar *) (dbuf)) + 1) = *pbuf_even;
			*(uchar *) dbuf = *pbuf_odd;
			dbuf += 1;
		}
	}
#else
	volatile ushort *pbuf =
		(ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	ushort *dbuf = (ushort *) sect_buf;

	debug("in input swap data base for read is %lx\n",
	      (unsigned long) pbuf);

	while (words--) {
#ifdef __MIPS__
		*dbuf++ = swab16p((u16 *) pbuf);
		*dbuf++ = swab16p((u16 *) pbuf);
#elif defined(CONFIG_PCS440EP)
		*dbuf++ = *pbuf;
		*dbuf++ = *pbuf;
#else
		*dbuf++ = ld_le16(pbuf);
		*dbuf++ = ld_le16(pbuf);
#endif /* !MIPS */
	}
#endif
}
#endif /* __LITTLE_ENDIAN || CONFIG_AU1X00 */


#if defined(CONFIG_IDE_SWAP_IO)
static void output_data(int dev, const ulong *sect_buf, int words)
{
#if defined(CONFIG_CPC45)
	uchar *dbuf;
	volatile uchar *pbuf_even;
	volatile uchar *pbuf_odd;

	pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
	pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
	dbuf = (uchar *) sect_buf;
	while (words--) {
		EIEIO;
		*pbuf_even = *dbuf++;
		EIEIO;
		*pbuf_odd = *dbuf++;
		EIEIO;
		*pbuf_even = *dbuf++;
		EIEIO;
		*pbuf_odd = *dbuf++;
	}
#else
	ushort *dbuf;
	volatile ushort *pbuf;

	pbuf = (ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	dbuf = (ushort *) sect_buf;
	while (words--) {
#if defined(CONFIG_PCS440EP)
		/* not tested, because CF was write protected */
		EIEIO;
		*pbuf = ld_le16(dbuf++);
		EIEIO;
		*pbuf = ld_le16(dbuf++);
#else
		EIEIO;
		*pbuf = *dbuf++;
		EIEIO;
		*pbuf = *dbuf++;
#endif
	}
#endif
}
#else  /* ! CONFIG_IDE_SWAP_IO */
static void output_data(int dev, const ulong *sect_buf, int words)
{
#if defined(CONFIG_IDE_AHB)
	ide_write_data(dev, sect_buf, words);
#else
	outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1);
#endif
}
#endif /* CONFIG_IDE_SWAP_IO */

#if defined(CONFIG_IDE_SWAP_IO)
static void input_data(int dev, ulong *sect_buf, int words)
{
#if defined(CONFIG_CPC45)
	uchar *dbuf;
	volatile uchar *pbuf_even;
	volatile uchar *pbuf_odd;

	pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
	pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
	dbuf = (uchar *) sect_buf;
	while (words--) {
		*dbuf++ = *pbuf_even;
		EIEIO;
		SYNC;
		*dbuf++ = *pbuf_odd;
		EIEIO;
		SYNC;
		*dbuf++ = *pbuf_even;
		EIEIO;
		SYNC;
		*dbuf++ = *pbuf_odd;
		EIEIO;
		SYNC;
	}
#else
	ushort *dbuf;
	volatile ushort *pbuf;

	pbuf = (ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	dbuf = (ushort *) sect_buf;

	debug("in input data base for read is %lx\n", (unsigned long) pbuf);

	while (words--) {
#if defined(CONFIG_PCS440EP)
		EIEIO;
		*dbuf++ = ld_le16(pbuf);
		EIEIO;
		*dbuf++ = ld_le16(pbuf);
#else
		EIEIO;
		*dbuf++ = *pbuf;
		EIEIO;
		*dbuf++ = *pbuf;
#endif
	}
#endif
}
#else  /* ! CONFIG_IDE_SWAP_IO */
static void input_data(int dev, ulong *sect_buf, int words)
{
#if defined(CONFIG_IDE_AHB)
	ide_read_data(dev, sect_buf, words);
#else
	insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1);
#endif
}

#endif /* CONFIG_IDE_SWAP_IO */

/* -------------------------------------------------------------------------
 */
static void ide_ident(block_dev_desc_t *dev_desc)
{
	unsigned char c;
	hd_driveid_t iop;

#ifdef CONFIG_ATAPI
	int retries = 0;
#endif

#ifdef CONFIG_TUNE_PIO
	int pio_mode;
#endif

#if 0
	int mode, cycle_time;
#endif
	int device;

	device = dev_desc->dev;
	printf("  Device %d: ", device);

	ide_led(DEVICE_LED(device), 1);	/* LED on       */
	/* Select device
	 */
	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
	dev_desc->if_type = IF_TYPE_IDE;
#ifdef CONFIG_ATAPI

	retries = 0;

	/* Warning: This will be tricky to read */
	while (retries <= 1) {
		/* check signature */
		if ((ide_inb(device, ATA_SECT_CNT) == 0x01) &&
		    (ide_inb(device, ATA_SECT_NUM) == 0x01) &&
		    (ide_inb(device, ATA_CYL_LOW) == 0x14) &&
		    (ide_inb(device, ATA_CYL_HIGH) == 0xEB)) {
			/* ATAPI Signature found */
			dev_desc->if_type = IF_TYPE_ATAPI;
			/*
			 * Start Ident Command
			 */
			ide_outb(device, ATA_COMMAND, ATAPI_CMD_IDENT);
			/*
			 * Wait for completion - ATAPI devices need more time
			 * to become ready
			 */
			c = ide_wait(device, ATAPI_TIME_OUT);
		} else
#endif
		{
			/*
			 * Start Ident Command
			 */
			ide_outb(device, ATA_COMMAND, ATA_CMD_IDENT);

			/*
			 * Wait for completion
			 */
			c = ide_wait(device, IDE_TIME_OUT);
		}
		ide_led(DEVICE_LED(device), 0);	/* LED off      */

		if (((c & ATA_STAT_DRQ) == 0) ||
		    ((c & (ATA_STAT_FAULT | ATA_STAT_ERR)) != 0)) {
#ifdef CONFIG_ATAPI
			{
				/*
				 * Need to soft reset the device
				 * in case it's an ATAPI...
				 */
				debug("Retrying...\n");
				ide_outb(device, ATA_DEV_HD,
					 ATA_LBA | ATA_DEVICE(device));
				udelay(100000);
				ide_outb(device, ATA_COMMAND, 0x08);
				udelay(500000);	/* 500 ms */
			}
			/*
			 * Select device
			 */
			ide_outb(device, ATA_DEV_HD,
				 ATA_LBA | ATA_DEVICE(device));
			retries++;
#else
			return;
#endif
		}
#ifdef CONFIG_ATAPI
		else
			break;
	}			/* see above - ugly to read */

	if (retries == 2)	/* Not found */
		return;
#endif

	input_swap_data(device, (ulong *)&iop, ATA_SECTORWORDS);

	ident_cpy((unsigned char *) dev_desc->revision, iop.fw_rev,
		  sizeof(dev_desc->revision));
	ident_cpy((unsigned char *) dev_desc->vendor, iop.model,
		  sizeof(dev_desc->vendor));
	ident_cpy((unsigned char *) dev_desc->product, iop.serial_no,
		  sizeof(dev_desc->product));
#ifdef __LITTLE_ENDIAN
	/*
	 * firmware revision, model, and serial number have Big Endian Byte
	 * order in Word. Convert all three to little endian.
	 *
	 * See CF+ and CompactFlash Specification Revision 2.0:
	 * 6.2.1.6: Identify Drive, Table 39 for more details
	 */

	strswab(dev_desc->revision);
	strswab(dev_desc->vendor);
	strswab(dev_desc->product);
#endif /* __LITTLE_ENDIAN */

	if ((iop.config & 0x0080) == 0x0080)
		dev_desc->removable = 1;
	else
		dev_desc->removable = 0;

#ifdef CONFIG_TUNE_PIO
	/* Mode 0 - 2 only, are directly determined by word 51. */
	pio_mode = iop.tPIO;
	if (pio_mode > 2) {
		printf("WARNING: Invalid PIO (word 51 = %d).\n", pio_mode);
		/* Force it to dead slow, and hope for the best... */
		pio_mode = 0;
	}

	/* Any CompactFlash Storage Card that supports PIO mode 3 or above
	 * shall set bit 1 of word 53 to one and support the fields contained
	 * in words 64 through 70.
	 */
	if (iop.field_valid & 0x02) {
		/*
		 * Mode 3 and above are possible.  Check in order from slow
		 * to fast, so we wind up with the highest mode allowed.
		 */
		if (iop.eide_pio_modes & 0x01)
			pio_mode = 3;
		if (iop.eide_pio_modes & 0x02)
			pio_mode = 4;
		if (ata_id_is_cfa((u16 *)&iop)) {
			if ((iop.cf_advanced_caps & 0x07) == 0x01)
				pio_mode = 5;
			if ((iop.cf_advanced_caps & 0x07) == 0x02)
				pio_mode = 6;
		}
	}

	/* System-specific, depends on bus speeds, etc. */
	ide_set_piomode(pio_mode);
#endif /* CONFIG_TUNE_PIO */

#if 0
	/*
	 * Drive PIO mode autoselection
	 */
	mode = iop.tPIO;

	printf("tPIO = 0x%02x = %d\n", mode, mode);
	if (mode > 2) {		/* 2 is maximum allowed tPIO value */
		mode = 2;
		debug("Override tPIO -> 2\n");
	}
	if (iop.field_valid & 2) {	/* drive implements ATA2? */
		debug("Drive implements ATA2\n");
		if (iop.capability & 8) {	/* drive supports use_iordy? */
			cycle_time = iop.eide_pio_iordy;
		} else {
			cycle_time = iop.eide_pio;
		}
		debug("cycle time = %d\n", cycle_time);
		mode = 4;
		if (cycle_time > 120)
			mode = 3;	/* 120 ns for PIO mode 4 */
		if (cycle_time > 180)
			mode = 2;	/* 180 ns for PIO mode 3 */
		if (cycle_time > 240)
			mode = 1;	/* 240 ns for PIO mode 4 */
		if (cycle_time > 383)
			mode = 0;	/* 383 ns for PIO mode 4 */
	}
	printf("PIO mode to use: PIO %d\n", mode);
#endif /* 0 */

#ifdef CONFIG_ATAPI
	if (dev_desc->if_type == IF_TYPE_ATAPI) {
		atapi_inquiry(dev_desc);
		return;
	}
#endif /* CONFIG_ATAPI */

#ifdef __BIG_ENDIAN
	/* swap shorts */
	dev_desc->lba = (iop.lba_capacity << 16) | (iop.lba_capacity >> 16);
#else  /* ! __BIG_ENDIAN */
	/*
	 * do not swap shorts on little endian
	 *
	 * See CF+ and CompactFlash Specification Revision 2.0:
	 * 6.2.1.6: Identfy Drive, Table 39, Word Address 57-58 for details.
	 */
	dev_desc->lba = iop.lba_capacity;
#endif /* __BIG_ENDIAN */

#ifdef CONFIG_LBA48
	if (iop.command_set_2 & 0x0400) {	/* LBA 48 support */
		dev_desc->lba48 = 1;
		dev_desc->lba = (unsigned long long) iop.lba48_capacity[0] |
			((unsigned long long) iop.lba48_capacity[1] << 16) |
			((unsigned long long) iop.lba48_capacity[2] << 32) |
			((unsigned long long) iop.lba48_capacity[3] << 48);
	} else {
		dev_desc->lba48 = 0;
	}
#endif /* CONFIG_LBA48 */
	/* assuming HD */
	dev_desc->type = DEV_TYPE_HARDDISK;
	dev_desc->blksz = ATA_BLOCKSIZE;
	dev_desc->lun = 0;	/* just to fill something in... */

#if 0				/* only used to test the powersaving mode,
				 * if enabled, the drive goes after 5 sec
				 * in standby mode */
	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
	c = ide_wait(device, IDE_TIME_OUT);
	ide_outb(device, ATA_SECT_CNT, 1);
	ide_outb(device, ATA_LBA_LOW, 0);
	ide_outb(device, ATA_LBA_MID, 0);
	ide_outb(device, ATA_LBA_HIGH, 0);
	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
	ide_outb(device, ATA_COMMAND, 0xe3);
	udelay(50);
	c = ide_wait(device, IDE_TIME_OUT);	/* can't take over 500 ms */
#endif
}


/* ------------------------------------------------------------------------- */

ulong ide_read(int device, lbaint_t blknr, ulong blkcnt, void *buffer)
{
	ulong n = 0;
	unsigned char c;
	unsigned char pwrsave = 0;	/* power save */

#ifdef CONFIG_LBA48
	unsigned char lba48 = 0;

	if (blknr & 0x0000fffff0000000ULL) {
		/* more than 28 bits used, use 48bit mode */
		lba48 = 1;
	}
#endif
	debug("ide_read dev %d start %lX, blocks %lX buffer at %lX\n",
	      device, blknr, blkcnt, (ulong) buffer);

	ide_led(DEVICE_LED(device), 1);	/* LED on       */

	/* Select device
	 */
	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
	c = ide_wait(device, IDE_TIME_OUT);

	if (c & ATA_STAT_BUSY) {
		printf("IDE read: device %d not ready\n", device);
		goto IDE_READ_E;
	}

	/* first check if the drive is in Powersaving mode, if yes,
	 * increase the timeout value */
	ide_outb(device, ATA_COMMAND, ATA_CMD_CHK_PWR);
	udelay(50);

	c = ide_wait(device, IDE_TIME_OUT);	/* can't take over 500 ms */

	if (c & ATA_STAT_BUSY) {
		printf("IDE read: device %d not ready\n", device);
		goto IDE_READ_E;
	}
	if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
		printf("No Powersaving mode %X\n", c);
	} else {
		c = ide_inb(device, ATA_SECT_CNT);
		debug("Powersaving %02X\n", c);
		if (c == 0)
			pwrsave = 1;
	}


	while (blkcnt-- > 0) {

		c = ide_wait(device, IDE_TIME_OUT);

		if (c & ATA_STAT_BUSY) {
			printf("IDE read: device %d not ready\n", device);
			break;
		}
#ifdef CONFIG_LBA48
		if (lba48) {
			/* write high bits */
			ide_outb(device, ATA_SECT_CNT, 0);
			ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
#ifdef CONFIG_SYS_64BIT_LBA
			ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
			ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
#else
			ide_outb(device, ATA_LBA_MID, 0);
			ide_outb(device, ATA_LBA_HIGH, 0);
#endif
		}
#endif
		ide_outb(device, ATA_SECT_CNT, 1);
		ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
		ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
		ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);

#ifdef CONFIG_LBA48
		if (lba48) {
			ide_outb(device, ATA_DEV_HD,
				 ATA_LBA | ATA_DEVICE(device));
			ide_outb(device, ATA_COMMAND, ATA_CMD_READ_EXT);

		} else
#endif
		{
			ide_outb(device, ATA_DEV_HD, ATA_LBA |
				 ATA_DEVICE(device) | ((blknr >> 24) & 0xF));
			ide_outb(device, ATA_COMMAND, ATA_CMD_READ);
		}

		udelay(50);

		if (pwrsave) {
			/* may take up to 4 sec */
			c = ide_wait(device, IDE_SPIN_UP_TIME_OUT);
			pwrsave = 0;
		} else {
			/* can't take over 500 ms */
			c = ide_wait(device, IDE_TIME_OUT);
		}

		if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) !=
		    ATA_STAT_DRQ) {
#if defined(CONFIG_SYS_64BIT_LBA)
			printf("Error (no IRQ) dev %d blk %lld: status 0x%02x\n",
				device, blknr, c);
#else
			printf("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
				device, (ulong) blknr, c);
#endif
			break;
		}

		input_data(device, buffer, ATA_SECTORWORDS);
		(void) ide_inb(device, ATA_STATUS);	/* clear IRQ */

		++n;
		++blknr;
		buffer += ATA_BLOCKSIZE;
	}
IDE_READ_E:
	ide_led(DEVICE_LED(device), 0);	/* LED off      */
	return (n);
}

/* ------------------------------------------------------------------------- */


ulong ide_write(int device, lbaint_t blknr, ulong blkcnt, const void *buffer)
{
	ulong n = 0;
	unsigned char c;

#ifdef CONFIG_LBA48
	unsigned char lba48 = 0;

	if (blknr & 0x0000fffff0000000ULL) {
		/* more than 28 bits used, use 48bit mode */
		lba48 = 1;
	}
#endif

	ide_led(DEVICE_LED(device), 1);	/* LED on       */

	/* Select device
	 */
	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));

	while (blkcnt-- > 0) {

		c = ide_wait(device, IDE_TIME_OUT);

		if (c & ATA_STAT_BUSY) {
			printf("IDE read: device %d not ready\n", device);
			goto WR_OUT;
		}
#ifdef CONFIG_LBA48
		if (lba48) {
			/* write high bits */
			ide_outb(device, ATA_SECT_CNT, 0);
			ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF);
#ifdef CONFIG_SYS_64BIT_LBA
			ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF);
			ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF);
#else
			ide_outb(device, ATA_LBA_MID, 0);
			ide_outb(device, ATA_LBA_HIGH, 0);
#endif
		}
#endif
		ide_outb(device, ATA_SECT_CNT, 1);
		ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
		ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
		ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);

#ifdef CONFIG_LBA48
		if (lba48) {
			ide_outb(device, ATA_DEV_HD,
				 ATA_LBA | ATA_DEVICE(device));
			ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE_EXT);

		} else
#endif
		{
			ide_outb(device, ATA_DEV_HD, ATA_LBA |
				 ATA_DEVICE(device) | ((blknr >> 24) & 0xF));
			ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE);
		}

		udelay(50);

		/* can't take over 500 ms */
		c = ide_wait(device, IDE_TIME_OUT);

		if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) !=
		    ATA_STAT_DRQ) {
#if defined(CONFIG_SYS_64BIT_LBA)
			printf("Error (no IRQ) dev %d blk %lld: status 0x%02x\n",
				device, blknr, c);
#else
			printf("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
				device, (ulong) blknr, c);
#endif
			goto WR_OUT;
		}

		output_data(device, buffer, ATA_SECTORWORDS);
		c = ide_inb(device, ATA_STATUS);	/* clear IRQ */
		++n;
		++blknr;
		buffer += ATA_BLOCKSIZE;
	}
WR_OUT:
	ide_led(DEVICE_LED(device), 0);	/* LED off      */
	return (n);
}

/* ------------------------------------------------------------------------- */

/*
 * copy src to dest, skipping leading and trailing blanks and null
 * terminate the string
 * "len" is the size of available memory including the terminating '\0'
 */
static void ident_cpy(unsigned char *dst, unsigned char *src,
		      unsigned int len)
{
	unsigned char *end, *last;

	last = dst;
	end = src + len - 1;

	/* reserve space for '\0' */
	if (len < 2)
		goto OUT;

	/* skip leading white space */
	while ((*src) && (src < end) && (*src == ' '))
		++src;

	/* copy string, omitting trailing white space */
	while ((*src) && (src < end)) {
		*dst++ = *src;
		if (*src++ != ' ')
			last = dst;
	}
OUT:
	*last = '\0';
}

/* ------------------------------------------------------------------------- */

/*
 * Wait until Busy bit is off, or timeout (in ms)
 * Return last status
 */
static uchar ide_wait(int dev, ulong t)
{
	ulong delay = 10 * t;	/* poll every 100 us */
	uchar c;

	while ((c = ide_inb(dev, ATA_STATUS)) & ATA_STAT_BUSY) {
		udelay(100);
		if (delay-- == 0)
			break;
	}
	return (c);
}

/* ------------------------------------------------------------------------- */

#ifdef CONFIG_IDE_RESET
extern void ide_set_reset(int idereset);

static void ide_reset(void)
{
#if defined(CONFIG_SYS_PB_12V_ENABLE) || defined(CONFIG_SYS_PB_IDE_MOTOR)
	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
#endif
	int i;

	curr_device = -1;
	for (i = 0; i < CONFIG_SYS_IDE_MAXBUS; ++i)
		ide_bus_ok[i] = 0;
	for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i)
		ide_dev_desc[i].type = DEV_TYPE_UNKNOWN;

	ide_set_reset(1);	/* assert reset */

	/* the reset signal shall be asserted for et least 25 us */
	udelay(25);

	WATCHDOG_RESET();

#ifdef CONFIG_SYS_PB_12V_ENABLE
	/* 12V Enable output OFF */
	immr->im_cpm.cp_pbdat &= ~(CONFIG_SYS_PB_12V_ENABLE);

	immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_12V_ENABLE);
	immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_12V_ENABLE);
	immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_12V_ENABLE;

	/* wait 500 ms for the voltage to stabilize */
	for (i = 0; i < 500; ++i)
		udelay(1000);

	/* 12V Enable output ON */
	immr->im_cpm.cp_pbdat |= CONFIG_SYS_PB_12V_ENABLE;
#endif /* CONFIG_SYS_PB_12V_ENABLE */

#ifdef CONFIG_SYS_PB_IDE_MOTOR
	/* configure IDE Motor voltage monitor pin as input */
	immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_IDE_MOTOR);
	immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_IDE_MOTOR);
	immr->im_cpm.cp_pbdir &= ~(CONFIG_SYS_PB_IDE_MOTOR);

	/* wait up to 1 s for the motor voltage to stabilize */
	for (i = 0; i < 1000; ++i) {
		if ((immr->im_cpm.cp_pbdat & CONFIG_SYS_PB_IDE_MOTOR) != 0) {
			break;
		}
		udelay(1000);
	}

	if (i == 1000) {	/* Timeout */
		printf("\nWarning: 5V for IDE Motor missing\n");
#ifdef CONFIG_STATUS_LED
#ifdef STATUS_LED_YELLOW
		status_led_set(STATUS_LED_YELLOW, STATUS_LED_ON);
#endif
#ifdef STATUS_LED_GREEN
		status_led_set(STATUS_LED_GREEN, STATUS_LED_OFF);
#endif
#endif /* CONFIG_STATUS_LED */
	}
#endif /* CONFIG_SYS_PB_IDE_MOTOR */

	WATCHDOG_RESET();

	/* de-assert RESET signal */
	ide_set_reset(0);

	/* wait 250 ms */
	for (i = 0; i < 250; ++i)
		udelay(1000);
}

#endif /* CONFIG_IDE_RESET */

/* ------------------------------------------------------------------------- */

#if defined(CONFIG_IDE_LED)	&& \
   !defined(CONFIG_CPC45)	&& \
   !defined(CONFIG_KUP4K)	&& \
   !defined(CONFIG_KUP4X)

static uchar led_buffer;	/* Buffer for current LED status        */

static void ide_led(uchar led, uchar status)
{
	uchar *led_port = LED_PORT;

	if (status)		/* switch LED on        */
		led_buffer |= led;
	else			/* switch LED off       */
		led_buffer &= ~led;

	*led_port = led_buffer;
}

#endif /* CONFIG_IDE_LED */

#if defined(CONFIG_OF_IDE_FIXUP)
int ide_device_present(int dev)
{
	if (dev >= CONFIG_SYS_IDE_MAXBUS)
		return 0;
	return (ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN ? 0 : 1);
}
#endif
/* ------------------------------------------------------------------------- */

#ifdef CONFIG_ATAPI
/****************************************************************************
 * ATAPI Support
 */

#if defined(CONFIG_IDE_SWAP_IO)
/* since ATAPI may use commands with not 4 bytes alligned length
 * we have our own transfer functions, 2 bytes alligned */
static void output_data_shorts(int dev, ushort *sect_buf, int shorts)
{
#if defined(CONFIG_CPC45)
	uchar *dbuf;
	volatile uchar *pbuf_even;
	volatile uchar *pbuf_odd;

	pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
	pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
	while (shorts--) {
		EIEIO;
		*pbuf_even = *dbuf++;
		EIEIO;
		*pbuf_odd = *dbuf++;
	}
#else
	ushort *dbuf;
	volatile ushort *pbuf;

	pbuf = (ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	dbuf = (ushort *) sect_buf;

	debug("in output data shorts base for read is %lx\n",
	      (unsigned long) pbuf);

	while (shorts--) {
		EIEIO;
		*pbuf = *dbuf++;
	}
#endif
}

static void input_data_shorts(int dev, ushort *sect_buf, int shorts)
{
#if defined(CONFIG_CPC45)
	uchar *dbuf;
	volatile uchar *pbuf_even;
	volatile uchar *pbuf_odd;

	pbuf_even = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_EVEN);
	pbuf_odd = (uchar *) (ATA_CURR_BASE(dev) + ATA_DATA_ODD);
	while (shorts--) {
		EIEIO;
		*dbuf++ = *pbuf_even;
		EIEIO;
		*dbuf++ = *pbuf_odd;
	}
#else
	ushort *dbuf;
	volatile ushort *pbuf;

	pbuf = (ushort *) (ATA_CURR_BASE(dev) + ATA_DATA_REG);
	dbuf = (ushort *) sect_buf;

	debug("in input data shorts base for read is %lx\n",
	      (unsigned long) pbuf);

	while (shorts--) {
		EIEIO;
		*dbuf++ = *pbuf;
	}
#endif
}

#else  /* ! CONFIG_IDE_SWAP_IO */
static void output_data_shorts(int dev, ushort *sect_buf, int shorts)
{
	outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts);
}

static void input_data_shorts(int dev, ushort *sect_buf, int shorts)
{
	insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts);
}

#endif /* CONFIG_IDE_SWAP_IO */

/*
 * Wait until (Status & mask) == res, or timeout (in ms)
 * Return last status
 * This is used since some ATAPI CD ROMs clears their Busy Bit first
 * and then they set their DRQ Bit
 */
static uchar atapi_wait_mask(int dev, ulong t, uchar mask, uchar res)
{
	ulong delay = 10 * t;	/* poll every 100 us */
	uchar c;

	/* prevents to read the status before valid */
	c = ide_inb(dev, ATA_DEV_CTL);

	while (((c = ide_inb(dev, ATA_STATUS)) & mask) != res) {
		/* break if error occurs (doesn't make sense to wait more) */
		if ((c & ATA_STAT_ERR) == ATA_STAT_ERR)
			break;
		udelay(100);
		if (delay-- == 0)
			break;
	}
	return (c);
}

/*
 * issue an atapi command
 */
unsigned char atapi_issue(int device, unsigned char *ccb, int ccblen,
			  unsigned char *buffer, int buflen)
{
	unsigned char c, err, mask, res;
	int n;

	ide_led(DEVICE_LED(device), 1);	/* LED on       */

	/* Select device
	 */
	mask = ATA_STAT_BUSY | ATA_STAT_DRQ;
	res = 0;
	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
	if ((c & mask) != res) {
		printf("ATAPI_ISSUE: device %d not ready status %X\n", device,
		       c);
		err = 0xFF;
		goto AI_OUT;
	}
	/* write taskfile */
	ide_outb(device, ATA_ERROR_REG, 0);	/* no DMA, no overlaped */
	ide_outb(device, ATA_SECT_CNT, 0);
	ide_outb(device, ATA_SECT_NUM, 0);
	ide_outb(device, ATA_CYL_LOW, (unsigned char) (buflen & 0xFF));
	ide_outb(device, ATA_CYL_HIGH,
		 (unsigned char) ((buflen >> 8) & 0xFF));
	ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));

	ide_outb(device, ATA_COMMAND, ATAPI_CMD_PACKET);
	udelay(50);

	mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR;
	res = ATA_STAT_DRQ;
	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);

	if ((c & mask) != res) {	/* DRQ must be 1, BSY 0 */
		printf("ATAPI_ISSUE: Error (no IRQ) before sending ccb dev %d status 0x%02x\n",
			device, c);
		err = 0xFF;
		goto AI_OUT;
	}

	/* write command block */
	output_data_shorts(device, (unsigned short *) ccb, ccblen / 2);

	/* ATAPI Command written wait for completition */
	udelay(5000);		/* device must set bsy */

	mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR;
	/*
	 * if no data wait for DRQ = 0 BSY = 0
	 * if data wait for DRQ = 1 BSY = 0
	 */
	res = 0;
	if (buflen)
		res = ATA_STAT_DRQ;
	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
	if ((c & mask) != res) {
		if (c & ATA_STAT_ERR) {
			err = (ide_inb(device, ATA_ERROR_REG)) >> 4;
			debug("atapi_issue 1 returned sense key %X status %02X\n",
				err, c);
		} else {
			printf("ATAPI_ISSUE: (no DRQ) after sending ccb (%x)  status 0x%02x\n",
				ccb[0], c);
			err = 0xFF;
		}
		goto AI_OUT;
	}
	n = ide_inb(device, ATA_CYL_HIGH);
	n <<= 8;
	n += ide_inb(device, ATA_CYL_LOW);
	if (n > buflen) {
		printf("ERROR, transfer bytes %d requested only %d\n", n,
		       buflen);
		err = 0xff;
		goto AI_OUT;
	}
	if ((n == 0) && (buflen < 0)) {
		printf("ERROR, transfer bytes %d requested %d\n", n, buflen);
		err = 0xff;
		goto AI_OUT;
	}
	if (n != buflen) {
		debug("WARNING, transfer bytes %d not equal with requested %d\n",
			n, buflen);
	}
	if (n != 0) {		/* data transfer */
		debug("ATAPI_ISSUE: %d Bytes to transfer\n", n);
		/* we transfer shorts */
		n >>= 1;
		/* ok now decide if it is an in or output */
		if ((ide_inb(device, ATA_SECT_CNT) & 0x02) == 0) {
			debug("Write to device\n");
			output_data_shorts(device, (unsigned short *) buffer,
					   n);
		} else {
			debug("Read from device @ %p shorts %d\n", buffer, n);
			input_data_shorts(device, (unsigned short *) buffer,
					  n);
		}
	}
	udelay(5000);		/* seems that some CD ROMs need this... */
	mask = ATA_STAT_BUSY | ATA_STAT_ERR;
	res = 0;
	c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res);
	if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
		err = (ide_inb(device, ATA_ERROR_REG) >> 4);
		debug("atapi_issue 2 returned sense key %X status %X\n", err,
		      c);
	} else {
		err = 0;
	}
AI_OUT:
	ide_led(DEVICE_LED(device), 0);	/* LED off      */
	return (err);
}

/*
 * sending the command to atapi_issue. If an status other than good
 * returns, an request_sense will be issued
 */

#define ATAPI_DRIVE_NOT_READY	100
#define ATAPI_UNIT_ATTN		10

unsigned char atapi_issue_autoreq(int device,
				  unsigned char *ccb,
				  int ccblen,
				  unsigned char *buffer, int buflen)
{
	unsigned char sense_data[18], sense_ccb[12];
	unsigned char res, key, asc, ascq;
	int notready, unitattn;

	unitattn = ATAPI_UNIT_ATTN;
	notready = ATAPI_DRIVE_NOT_READY;

retry:
	res = atapi_issue(device, ccb, ccblen, buffer, buflen);
	if (res == 0)
		return 0;	/* Ok */

	if (res == 0xFF)
		return 0xFF;	/* error */

	debug("(auto_req)atapi_issue returned sense key %X\n", res);

	memset(sense_ccb, 0, sizeof(sense_ccb));
	memset(sense_data, 0, sizeof(sense_data));
	sense_ccb[0] = ATAPI_CMD_REQ_SENSE;
	sense_ccb[4] = 18;	/* allocation Length */

	res = atapi_issue(device, sense_ccb, 12, sense_data, 18);
	key = (sense_data[2] & 0xF);
	asc = (sense_data[12]);
	ascq = (sense_data[13]);

	debug("ATAPI_CMD_REQ_SENSE returned %x\n", res);
	debug(" Sense page: %02X key %02X ASC %02X ASCQ %02X\n",
	      sense_data[0], key, asc, ascq);

	if ((key == 0))
		return 0;	/* ok device ready */

	if ((key == 6) || (asc == 0x29) || (asc == 0x28)) { /* Unit Attention */
		if (unitattn-- > 0) {
			udelay(200 * 1000);
			goto retry;
		}
		printf("Unit Attention, tried %d\n", ATAPI_UNIT_ATTN);
		goto error;
	}
	if ((asc == 0x4) && (ascq == 0x1)) {
		/* not ready, but will be ready soon */
		if (notready-- > 0) {
			udelay(200 * 1000);
			goto retry;
		}
		printf("Drive not ready, tried %d times\n",
		       ATAPI_DRIVE_NOT_READY);
		goto error;
	}
	if (asc == 0x3a) {
		debug("Media not present\n");
		goto error;
	}

	printf("ERROR: Unknown Sense key %02X ASC %02X ASCQ %02X\n", key, asc,
	       ascq);
error:
	debug("ERROR Sense key %02X ASC %02X ASCQ %02X\n", key, asc, ascq);
	return (0xFF);
}


static void atapi_inquiry(block_dev_desc_t *dev_desc)
{
	unsigned char ccb[12];	/* Command descriptor block */
	unsigned char iobuf[64];	/* temp buf */
	unsigned char c;
	int device;

	device = dev_desc->dev;
	dev_desc->type = DEV_TYPE_UNKNOWN;	/* not yet valid */
	dev_desc->block_read = atapi_read;

	memset(ccb, 0, sizeof(ccb));
	memset(iobuf, 0, sizeof(iobuf));

	ccb[0] = ATAPI_CMD_INQUIRY;
	ccb[4] = 40;		/* allocation Legnth */
	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *) iobuf, 40);

	debug("ATAPI_CMD_INQUIRY returned %x\n", c);
	if (c != 0)
		return;

	/* copy device ident strings */
	ident_cpy((unsigned char *) dev_desc->vendor, &iobuf[8], 8);
	ident_cpy((unsigned char *) dev_desc->product, &iobuf[16], 16);
	ident_cpy((unsigned char *) dev_desc->revision, &iobuf[32], 5);

	dev_desc->lun = 0;
	dev_desc->lba = 0;
	dev_desc->blksz = 0;
	dev_desc->type = iobuf[0] & 0x1f;

	if ((iobuf[1] & 0x80) == 0x80)
		dev_desc->removable = 1;
	else
		dev_desc->removable = 0;

	memset(ccb, 0, sizeof(ccb));
	memset(iobuf, 0, sizeof(iobuf));
	ccb[0] = ATAPI_CMD_START_STOP;
	ccb[4] = 0x03;		/* start */

	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *) iobuf, 0);

	debug("ATAPI_CMD_START_STOP returned %x\n", c);
	if (c != 0)
		return;

	memset(ccb, 0, sizeof(ccb));
	memset(iobuf, 0, sizeof(iobuf));
	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *) iobuf, 0);

	debug("ATAPI_CMD_UNIT_TEST_READY returned %x\n", c);
	if (c != 0)
		return;

	memset(ccb, 0, sizeof(ccb));
	memset(iobuf, 0, sizeof(iobuf));
	ccb[0] = ATAPI_CMD_READ_CAP;
	c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *) iobuf, 8);
	debug("ATAPI_CMD_READ_CAP returned %x\n", c);
	if (c != 0)
		return;

	debug("Read Cap: LBA %02X%02X%02X%02X blksize %02X%02X%02X%02X\n",
	      iobuf[0], iobuf[1], iobuf[2], iobuf[3],
	      iobuf[4], iobuf[5], iobuf[6], iobuf[7]);

	dev_desc->lba = ((unsigned long) iobuf[0] << 24) +
		((unsigned long) iobuf[1] << 16) +
		((unsigned long) iobuf[2] << 8) + ((unsigned long) iobuf[3]);
	dev_desc->blksz = ((unsigned long) iobuf[4] << 24) +
		((unsigned long) iobuf[5] << 16) +
		((unsigned long) iobuf[6] << 8) + ((unsigned long) iobuf[7]);
#ifdef CONFIG_LBA48
	/* ATAPI devices cannot use 48bit addressing (ATA/ATAPI v7) */
	dev_desc->lba48 = 0;
#endif
	return;
}


/*
 * atapi_read:
 * we transfer only one block per command, since the multiple DRQ per
 * command is not yet implemented
 */
#define ATAPI_READ_MAX_BYTES	2048	/* we read max 2kbytes */
#define ATAPI_READ_BLOCK_SIZE	2048	/* assuming CD part */
#define ATAPI_READ_MAX_BLOCK	(ATAPI_READ_MAX_BYTES/ATAPI_READ_BLOCK_SIZE)

ulong atapi_read(int device, lbaint_t blknr, ulong blkcnt, void *buffer)
{
	ulong n = 0;
	unsigned char ccb[12];	/* Command descriptor block */
	ulong cnt;

	debug("atapi_read dev %d start %lX, blocks %lX buffer at %lX\n",
	      device, blknr, blkcnt, (ulong) buffer);

	do {
		if (blkcnt > ATAPI_READ_MAX_BLOCK)
			cnt = ATAPI_READ_MAX_BLOCK;
		else
			cnt = blkcnt;

		ccb[0] = ATAPI_CMD_READ_12;
		ccb[1] = 0;	/* reserved */
		ccb[2] = (unsigned char) (blknr >> 24) & 0xFF;	/* MSB Block */
		ccb[3] = (unsigned char) (blknr >> 16) & 0xFF;	/*  */
		ccb[4] = (unsigned char) (blknr >> 8) & 0xFF;
		ccb[5] = (unsigned char) blknr & 0xFF;	/* LSB Block */
		ccb[6] = (unsigned char) (cnt >> 24) & 0xFF; /* MSB Block cnt */
		ccb[7] = (unsigned char) (cnt >> 16) & 0xFF;
		ccb[8] = (unsigned char) (cnt >> 8) & 0xFF;
		ccb[9] = (unsigned char) cnt & 0xFF;	/* LSB Block */
		ccb[10] = 0;	/* reserved */
		ccb[11] = 0;	/* reserved */

		if (atapi_issue_autoreq(device, ccb, 12,
					(unsigned char *) buffer,
					cnt * ATAPI_READ_BLOCK_SIZE)
		    == 0xFF) {
			return (n);
		}
		n += cnt;
		blkcnt -= cnt;
		blknr += cnt;
		buffer += (cnt * ATAPI_READ_BLOCK_SIZE);
	} while (blkcnt > 0);
	return (n);
}

/* ------------------------------------------------------------------------- */

#endif /* CONFIG_ATAPI */

U_BOOT_CMD(ide, 5, 1, do_ide,
	   "IDE sub-system",
	   "reset - reset IDE controller\n"
	   "ide info  - show available IDE devices\n"
	   "ide device [dev] - show or set current device\n"
	   "ide part [dev] - print partition table of one or all IDE devices\n"
	   "ide read  addr blk# cnt\n"
	   "ide write addr blk# cnt - read/write `cnt'"
	   " blocks starting at block `blk#'\n"
	   "    to/from memory address `addr'");

U_BOOT_CMD(diskboot, 3, 1, do_diskboot,
	   "boot from IDE device", "loadAddr dev:part");